View MC10H351_113762.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad TTL/NMOS to PECL* Translator
The MC10H351 is a quad translator for interfacing data between a saturated logic section and the PECL section of digital systems when only a +5.0 Vdc power supply is available. The MC10H351 has TTL/NMOS compatible inputs and PECL complementary open-emitter outputs that allow use as an inverting/non-inverting translator or as a differential line driver. When the common strobe input is at a low logic level, it forces all true outputs to the PECL low logic state ( +3.2 V) and all inverting outputs to the PECL high logic state ( +4.1 V). The MC10H351 can also be used with the MC10H350 to transmit and receive TTL/NMOS information differentially via balanced twisted pair lines. * * * * Single +5.0 Power Supply All VCC Pins Isolated On Chip Differentially Drive Balanced Lines tpd = 1.3 nsec Typical
MC10H351
L SUFFIX CERAMIC PACKAGE CASE 732-03 P SUFFIX PLASTIC PACKAGE CASE 738-03 FN SUFFIX PLCC CASE 775-02
LOGIC DIAGRAM
B IN A IN 7 8 12 1 2 5 4 Symbol VCC VI Iout TA Tstg Rating 0 to +7.0 0 to VCC 50 100 0 to +75 -55 to +150 -55 to +165 Unit Vdc Vdc mA C C D IN 16 17 C IN 14 COMMON 9 STROBE 19 18 B OUT B OUT A OUT A OUT D OUT D OUT C OUT C OUT
MAXIMUM RATINGS
Characteristic Power Supply Input Voltage (VCC = 5.0 V) Output Current -- Continuous -- Surge Operating Temperature Range Storage Temperature Range -- Plastic -- Ceramic
VCC (+5.0 VDC) = PINS 6, 11, 15, 20 GND = PIN 10
ELECTRICAL CHARACTERISTICS (VCC = VCC1 = VCC2 = 5.0 V 5.0%)
0 Characteristic Power Supply pp y Current C t Reverse Current Pins 7, 8, 12, 14 Pin 9 Forward Current Pins 7, 8, 12, 14 Pin 9 Input Breakdown Voltage Input Clamp Voltage (Iin = -18 mA) High Output Voltage (1) Low Output Voltage (1) High Input Voltage Low Input Voltage Symbol ECL TTL IR IINH IF IINL V(BR)in VI VOH VOL VIH VIL Min -- -- -- -- -- -- 5.5 -- 3.98 3.05 2.0 -- Max 50 20 25 100 -0.8 -3.2 -- -1.5 4.16 3.37 -- 0.8 Min -- -- -- -- -- -- 5.5 -- 4.02 3.05 2.0 -- 25 Max 45 15 20 80 -0.6 -2.4 -- -1.5 4.19 3.37 -- 0.8 Min -- -- -- -- -- -- 5.5 -- 4.08 3.05 2.0 -- 75 Max 50 20 25 100 mA -0.8 -3.2 -- -1.5 4.27 3.37 -- 0.8 Vdc Vdc Vdc Vdc Vdc Vdc Unit mA mA A B OUT B OUT N.C. A OUT A OUT VCC B IN A IN COMMON STROBE GND
DIP PIN ASSIGNMENT
1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 ECL VCC C OUT C OUT D OUT D OUT VCC 2 C IN N.C. D IN TTL VCC
Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6-36 of the Motorola MECL Data Book (DL122/D).
(1) With VCC at 5.0 V. VOH/VOL change 1:1 with VCC. *Positive Emitter Coupled Logic 3/93
(c) Motorola, Inc. 1996
2-77
REV 5
MC10H351
AC PARAMETERS
0 Characteristic Propagation Delay (1) Rise Time (20% to 80%) Fall Time (80% to 20%) Maximum Operating Frequency Symbol tpd tr tf fmax Min 0.4 0.4 0.4 150 Max 2.2 1.9 1.9 -- Min 0.4 0.4 0.4 150 25 Max 2.2 2.0 2.0 -- Min 0.4 0.4 0.4 150 75 Max 2.1 2.1 2.1 -- Unit ns ns ns MHz
(1) Propagation delay is measured on this circuit from +1.5 volts on the input waveform to the 50% point on the output waveform. NOTE: Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained. Outputs are terminated through a 50-ohm resistor to VCC -2.0 Vdc.
MOTOROLA
2-78
MECL Data DL122 -- Rev 6
MC10H351
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE C
B -N- Y BRK D -L- -M- W D Z
0.007 (0.180) M T L-M U
S
N
S S
0.007 (0.180) M T L-M
N
S
20
1
X V VIEW D-D
G1
0.010 (0.250)
S
T L-M
S
N
S
A Z R
0.007 (0.180) M T L-M 0.007 (0.180) M T L-M
S
N N
S
S
S
H
0.007 (0.180) M T L-M
S
N
S
C
E 0.004 (0.100) G G1 0.010 (0.250) S T L-M J -T-
SEATING PLANE
K1 K F VIEW S 0.007 (0.180)
M
VIEW S
S
T L-M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.310 0.330 0.040 ---
MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10 _ 7.88 8.38 1.02 ---
MECL Data DL122 -- Rev 6
2-79
MOTOROLA
MC10H351
OUTLINE DIMENSIONS
L SUFFIX CERAMIC DIP PACKAGE CASE 732-03 ISSUE E
20 1
11 10
NOTES: 1. LEADS WITHIN 0.010 DIAMETER, TRUE POSITION AT SEATING PLANE, AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSIONS A AND B INCLUDE MENISCUS. INCHES MIN MAX 0.940 0.990 0.260 0.295 0.150 0.200 0.015 0.022 0.055 0.065 0.100 BSC 0.020 0.050 0.008 0.012 0.125 0.160 0.300 BSC 0_ 15_ 0.010 0.040
B A F C L
DIM A B C D F G H J K L M N
N H D
SEATING PLANE
G
K
J M
-A-
20 11
P SUFFIX PLASTIC DIP PACKAGE CASE 738-03 ISSUE E
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 25.66 27.17 6.10 6.60 3.81 4.57 0.39 0.55 1.27 BSC 1.27 1.77 2.54 BSC 0.21 0.38 2.80 3.55 7.62 BSC 0_ 15_ 0.51 1.01
B
1 10
C
L
-T-
SEATING PLANE
K M E G F D
20 PL
N J 0.25 (0.010)
M 20 PL
0.25 (0.010) TA
M
M
TB
M
DIM A B C D E F G J K L M N
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-80
*MC10H351/D*
MC10H351/D MECL Data DL122 -- Rev 6

▲Up To Search▲

Price & Availability of MC10H351

	To Download MC10H351 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .